Keurig espresso makers are a preferred solution to make a fast and straightforward cup of espresso. Nevertheless, in case your Keurig begins to malfunction, it’s possible you’ll must take it aside to troubleshoot the issue. Taking aside a Keurig can seem to be a frightening process, however it’s truly fairly easy with the correct instruments and directions.
Earlier than you begin taking aside your Keurig, make sure you unplug it from the facility outlet. Additionally, you will want to assemble just a few instruments, together with a Phillips head screwdriver, a flathead screwdriver, and a pair of pliers. Upon getting your instruments, you may comply with the steps beneath to take aside your Keurig:
First, take away the water reservoir. The water reservoir is positioned on the again of the Keurig. To take away it, merely raise it up and pull it out. Subsequent, take away the drip tray. The drip tray is positioned beneath the brew head. To take away it, merely pull it out. Lastly, take away the brew head. The brew head is positioned on the prime of the Keurig. To take away it, flip the locking lever to the unlock place and pull the brew head up and out.
Disassembling the Outer Casing
Earlier than you may entry the inside workings of your Keurig, you should disassemble the outer casing. It is a comparatively easy course of, nevertheless it’s necessary to comply with the steps rigorously to keep away from damaging your espresso maker.
1. Take away the highest cowl
Begin by eradicating the highest cowl of the Keurig. On most fashions, the highest cowl is held in place by two screws positioned behind the machine. Use a Phillips head screwdriver to take away the screws, then raise the highest cowl off the machine.
As soon as the highest cowl is eliminated, you will note the water reservoir and the brewing chamber. The water reservoir is positioned on the left aspect of the machine, and the brewing chamber is positioned on the correct aspect.
To take away the water reservoir, merely raise it up and out of the machine. To take away the brewing chamber, press down on the discharge button positioned on the highest of the chamber, then raise the chamber out of the machine.
2. Take away the aspect panels
The subsequent step is to take away the aspect panels of the Keurig. On most fashions, the aspect panels are held in place by two screws positioned on the prime and backside of every panel. Use a Phillips head screwdriver to take away the screws, then raise the aspect panels off the machine.
As soon as the aspect panels are eliminated, you will note the inner elements of the Keurig. These elements embrace the heating ingredient, the pump, and the management board.
3. Take away the underside cowl
The ultimate step is to take away the underside cowl of the Keurig. On most fashions, the underside cowl is held in place by 4 screws positioned on the corners of the duvet. Use a Phillips head screwdriver to take away the screws, then raise the underside cowl off the machine.
As soon as the underside cowl is eliminated, you’ll have entry to all the inner elements of the Keurig. Now you can start troubleshooting or repairing your espresso maker.
Eradicating the Water Reservoir
Eradicating the water reservoir is straightforward and could be carried out in only a few steps. Make it possible for the espresso maker is turned off and unplugged earlier than beginning.
1. Find the water reservoir launch button.
The water reservoir launch button is often positioned on the again or aspect of the espresso maker. It’s usually a small, black button.
2. Press the water reservoir launch button and pull the reservoir straight up.
Upon getting positioned the water reservoir launch button, press it and pull the reservoir straight up. The reservoir ought to come out simply. If you’re having hassle eradicating the reservoir, strive wiggling it gently back and forth.
The reservoir has quite a lot of inner elements that will dislodge through the elimination or filling course of. Here is a visible information to assist establish these elements:
| Part | Description |
|---|---|
| Water Stage Indicator | A float that rises and falls with the water stage. |
| Water Stage Sensor | A sensor that detects the water stage and shuts off the espresso maker when the reservoir is empty. |
| Pump | A pump that circulates the water by way of the espresso maker. |
3. As soon as the reservoir has been eliminated, you may clear it with heat, soapy water.
Be sure to rinse the reservoir totally and permit it to dry fully earlier than changing it.
Disconnecting the Electrical Wires
As soon as you’ve got eliminated the outer casing, it is time to disconnect {the electrical} wires. These wires are what energy the Keurig, so it is necessary to watch out when dealing with them.
Step 1: Find the Electrical Wires
{The electrical} wires are positioned on the underside of the Keurig. They’re often held in place by a plastic clip.
Step 2: Take away the Plastic Clip
Use a screwdriver or your fingernails to take away the plastic clip. This may launch {the electrical} wires.
Step 3: Disconnect the Electrical Wires
As soon as {the electrical} wires are launched, you may disconnect them. To do that, merely pull the wires aside.
| Wire Colour | Connection |
|---|---|
| Black | Frequent |
| Purple | Line |
| White | Impartial |
Eradicating the Plunger and Needles
To take away the plunger and needles, first take away the highest cowl of the Keurig. Then, find the plunger meeting. It’s a cylindrical-shaped half that’s positioned within the middle of the machine. Grip the plunger meeting and pull it straight up. This may take away the plunger and needles from the machine.
As soon as the plunger and needles have been eliminated, you may clear them. To wash the plunger, merely wipe it down with a humid material. To wash the needles, use a tender brush to take away any espresso grounds or particles. As soon as the plunger and needles are clear, you may reassemble the Keurig.
Cleansing the Plunger Meeting
| Step | Description |
|---|---|
| 1 | Take away the highest cowl of the Keurig. |
| 2 | Find the plunger meeting. It’s a cylindrical-shaped half that’s positioned within the middle of the machine. |
| 3 | Grip the plunger meeting and pull it straight up. This may take away the plunger and needles from the machine. |
| 4 | Wipe down the plunger with a humid material. |
| 5 | Use a tender brush to take away any espresso grounds or particles from the needles. |
| 6 | Reassemble the Keurig. |
Accessing the Inside Elements
To entry the inner elements of the Keurig machine, it’s essential to rigorously disassemble the outside housing. Here is a step-by-step information to take action:
1. Unplug the Machine
Start by unplugging the Keurig machine from the facility outlet to make sure your security.
2. Find the Screws
Subsequent, find the screws that maintain the outside housing collectively. On most Keurig fashions, these screws are discovered on the again of the machine or beneath the drip tray.
3. Take away the Exterior Housing
Use a screwdriver to take away the screws, after which gently raise the outside housing off the machine. Watch out to not harm any wires or inner elements.
4. Find the Screws Holding the Chassis
Inside the outside housing, one can find the chassis, which holds the inner elements in place. Find the screws that maintain the chassis in place, that are usually discovered on the edges or backside.
5. Take away the Chassis
Use a screwdriver to take away the screws, after which rigorously raise the chassis out of the machine. Take care to not pull any wires or harm any elements.
6. Troubleshooting
Typically throughout disassembly, it’s possible you’ll encounter some frequent points. Here is a troubleshooting information that will help you resolve them:
| Subject | Answer |
|---|---|
| Stripped screw | Use a rubber band or small piece of paper between the screwdriver and the screw to realize further grip. |
| Caught elements | Gently faucet on the part with a rubber mallet or use a skinny, flat software to pry it aside. |
| Broken or disconnected wires | Examine the wires for any harm or disconnection. If vital, reconnect or restore the wires utilizing wire connectors or electrical tape. |
Disconnecting the Management Board
As soon as you’ve got eliminated the highest cowl and entrance panel, it is time to disconnect the management board. It is a delicate step, so take your time and watch out to not harm any of the elements.
Step 1: Establish the Management Board
The management board is often positioned within the middle of the machine, behind the entrance panel. It is a inexperienced circuit board with numerous wires and connectors connected to it.
Step 2: Disconnect the Wires
Use a pair of needle-nose pliers to disconnect the wires from the management board. There are two sorts of wires: energy wires and knowledge wires. Energy wires are often thicker and have a black or pink insulation. Information wires are thinner and have a yellow or white insulation.
Step 3: Take away the Connectors
As soon as the wires are disconnected, you may take away the connectors from the management board. Connectors are small plastic plugs that join the wires to the board. To take away a connector, gently pry it up with a small screwdriver.
Step 4: Carry the Management Board
As soon as the connectors are eliminated, you may raise the management board up and out of the machine. Watch out to not harm any of the elements on the board.
Step 5: Place the Management Board in a Secure Location
As soon as the management board is eliminated, place it in a protected location the place it will not get broken. You may put it in a plastic bag or wrap it in a towel.
Step 6: Double-Examine Your Work
Earlier than you progress on to the following step, double-check your work to guarantee that all the wires and connectors are disconnected from the management board. This may assist to forestall any harm to the machine if you reassemble it.
Step 7: Troubleshooting Suggestions
Should you’re having hassle disconnecting the management board, listed here are just a few troubleshooting ideas:
| Drawback | Answer |
|---|---|
| I am unable to disconnect the wires from the management board. | Just remember to’re utilizing the right sort of pliers. Needle-nose pliers are the very best sort of pliers for this job. |
| I am unable to take away the connectors from the management board. | Strive utilizing a small screwdriver to softly pry the connectors up. Watch out to not harm the connectors or the board. |
| I by chance broken the management board. | Should you by chance broken the management board, you will have to switch it. You should purchase a alternative management board from the producer of your Keurig machine. |
Eradicating the Circulate Sensor
The circulation sensor is a small, plastic part positioned within the water line of your Keurig. It helps to find out how a lot water is pumped into the brew chamber. To take away the circulation sensor, comply with these steps:
1. Unplug the Keurig
Earlier than you start, guarantee that the Keurig is unplugged from {the electrical} outlet.
2. Find the circulation sensor
The circulation sensor is positioned on the underside of the Keurig, close to the water line.
3. Take away the screws
There are two screws that maintain the circulation sensor in place. Take away these screws utilizing a Phillips head screwdriver.
4. Disconnect the wires
As soon as the screws are eliminated, you will have to disconnect the 2 wires which might be linked to the circulation sensor.
5. Take away the circulation sensor
As soon as the wires are disconnected, you may take away the circulation sensor by gently pulling it out of the water line.
6. Examine the circulation sensor
Upon getting eliminated the circulation sensor, take a second to examine it for any harm. If the circulation sensor is broken, it can have to be changed.
7. Clear the circulation sensor
If the circulation sensor isn’t broken, you may clear it by rinsing it with water.
8. Reinstall the circulation sensor
To reinstall the circulation sensor, merely reverse the steps that you simply took to take away it. Remember to tighten the screws securely, however don’t overtighten them.
Disassembling the Drip Tray
1. **Find the drip tray latch:** The drip tray is held in place by a latch positioned on the underside of the machine.
2. **Press the latch:** Firmly press down on the latch to launch it.
3. **Pull out the drip tray:** As soon as the latch is launched, gently pull out the drip tray.
4. **Take away the cup assist:** The cup assist is a small plastic piece that sits contained in the drip tray. Grasp the cup assist and pull it straight as much as take away it.
5. **Clear the drip tray and cup assist:** Use a humid material to wipe down the drip tray and cup assist. If there may be any espresso residue, use a light detergent to scrub it off.
6. **Reassemble the drip tray:** Place the cup assist again into the drip tray, then insert the drip tray again into the machine.
7. **Shut the latch:** Push down on the latch to safe the drip tray in place.
Eradicating the Drip Tray Float
8. **Find the drip tray float:** The drip tray float is a small plastic ball that sits contained in the drip tray. It helps to detect when the drip tray is full.
9. **Take away the drip tray float:** To take away the drip tray float, gently push down on the float and pull it out of the drip tray. The float is held in place by a small magnet, so it might require a little bit drive to take away it.
| Step | Motion |
|---|---|
| 1 | Find the drip tray latch. |
| 2 | Press the latch. |
| 3 | Pull out the drip tray. |
| 4 | Take away the cup assist. |
| 5 | Clear the drip tray and cup assist. |
| 6 | Reassemble the drip tray. |
| 7 | Shut the latch. |
| 8 | Find the drip tray float. |
| 9 | Take away the drip tray float. |
Cleansing and Reassembling the Elements
Now that the Keurig is disassembled, it is time to clear the elements. Use heat, soapy water and a tender material to wipe down all the detachable components. Take particular care to scrub the needle and the water reservoir.
As soon as the elements are clear, it is time to reassemble the Keurig. Begin by inserting the water reservoir into the bottom of the machine. Then, exchange the drip tray and the Ok-Cup holder.
Subsequent, insert the needle into the highest of the machine. Make it possible for the needle is correctly aligned in order that it will probably puncture the Ok-Cups.
Lastly, exchange the highest of the machine and plug within the Keurig. Your Keurig is now prepared to make use of!
Cleansing the Water Reservoir
The water reservoir is without doubt one of the most necessary elements of your Keurig. It is necessary to scrub the water reservoir usually to forestall the buildup of mildew and micro organism.
To wash the water reservoir, take away it from the Keurig and rinse it with heat water. Then, add just a few drops of dish cleaning soap to the water reservoir and swish it round. Lastly, rinse the water reservoir totally with heat water and exchange it within the Keurig.
Cleansing the Needle
The needle is one other necessary part of your Keurig. It is necessary to scrub the needle usually to forestall it from clogging. Some keurig fashions have a detachable needle, whereas others don’t. To wash the needle, merely use a tender material and gently wipe away any espresso grounds or different particles. In case your Keurig mannequin has a detachable needle, you may take away it and soak it in heat, soapy water for a couple of minutes. Then, rinse the needle totally with heat water and exchange it within the Keurig.
Cleansing the Ok-Cup Holder
The Ok-Cup holder is one other part of your Keurig that needs to be cleaned usually. To wash the Ok-Cup holder, merely take away it from the Keurig and rinse it with heat water. Then, use a tender material to wipe away any espresso grounds or different particles. Lastly, exchange the Ok-Cup holder within the Keurig.
| Kind | Cleansing technique |
|---|---|
| Water reservoir | Rinse with heat water, add just a few drops of dish cleaning soap, swish round, rinse totally |
| Needle | Wipe with a tender material, take away and soak in heat, soapy water (if detachable) |
| Ok-Cup holder | Rinse with heat water, wipe with a tender material |
How To Take Aside A Keurig
Listed here are the steps on how you can take aside a Keurig:
- Unplug the Keurig and let it settle down.
- Take away the water reservoir and drip tray.
- Flip the Keurig the other way up and take away the 4 screws that maintain the underside panel in place.
- Rigorously raise the underside panel off of the Keurig.
- Find the 2 screws that maintain the heating ingredient in place and take away them.
- Rigorously raise the heating ingredient out of the Keurig.
- Find the 2 screws that maintain the pump in place and take away them.
- Rigorously raise the pump out of the Keurig.
- Find the 2 screws that maintain the management board in place and take away them.
- Rigorously raise the management board out of the Keurig.
Individuals Additionally Ask About How To Take Aside A Keurig
How do I clear the within of my Keurig?
To wash the within of your Keurig, you will have to descale it. Descaling is the method of eradicating mineral buildup from the within of the Keurig. You may descale your Keurig utilizing a descaling resolution or vinegar.
How do I repair a Keurig that’s not brewing?
In case your Keurig isn’t brewing, there are some things you may verify:
- Make it possible for the Keurig is plugged in and turned on.
- Make it possible for there may be water within the water reservoir.
- Make it possible for the Ok-cup is correctly inserted into the Keurig.
- Make it possible for the needle within the Keurig isn’t clogged.
How do I exchange the water filter in my Keurig?
To exchange the water filter in your Keurig, you will have to:
- Take away the water reservoir from the Keurig.
- Find the water filter within the backside of the water reservoir.
- Take away the outdated water filter and insert the brand new water filter.
- Exchange the water reservoir within the Keurig.
