The Rolex watch is a luxurious timepiece that’s identified for its high quality and craftsmanship. Nevertheless, even the best watches require upkeep sometimes, and some of the widespread upkeep duties is eradicating the again of the watch. This could be a difficult activity, however it’s one that may be completed at residence with the correct instruments and information.
Earlier than you start, it is very important collect the required instruments. You will have a small screwdriver, a case knife or butter knife, and a tender material. You may additionally need to use a pair of tweezers that can assist you take away the again of the watch. After you have your instruments, you’ll be able to start the method of eradicating the again of the watch.
To take away the again of the watch, you will want to first find the small notch on the facet of the case. This notch is often positioned close to the 6 o’clock place. After you have discovered the notch, you will want to insert the tip of the screwdriver into the notch and pry the again of the watch open. Watch out to not pry too exhausting, as you do not need to break the watch. As soon as the again of the watch is open, you will want to make use of the case knife or butter knife to take away the gasket. The gasket is a rubber ring that helps to seal the again of the watch and stop water from getting into. As soon as the gasket has been eliminated, it is possible for you to to entry the motion of the watch.
Instruments and Preparation
To efficiently take away the again of a Rolex watch, you will want the next instruments and supplies:
Important Instruments:
| Instrument | Objective |
|---|---|
| Caseback elimination device | 专门用于移除 Rolex 手表的表背。 |
| Crystal press | 在更换表镜时，可用来将表镜压入表壳。 |
| Spring bar device | 用于移除表带或表链上的弹簧杆。 |
| 镊子 | 用于取出微小的部件或垫圈。 |
| 手套 | 保护手表免受指纹和污垢影响。 |
可选工具：
| Instrument | Objective |
|---|---|
| 手表清洁液 | 清洁表壳和表背。 |
| 备用垫圈 | 如有必要，可更换表背垫圈。 |
| 除锈剂 | 去除表背和表壳上的锈迹。 |
| Case Kind | Rotation Route |
|---|---|
| Oyster Case | Counterclockwise |
| Snap-On Case | Counterclockwise |
| Screw-On Case | Clockwise |
Troubleshooting Frequent Points
Problem: The watch remains to be beneath guarantee.
If the watch remains to be beneath guarantee and you might be experiencing issues, it’s best to contact your nearest Rolex licensed supplier. They’ll be capable to diagnose and restore the watch at no cost.
Problem: The watch isn’t beneath guarantee.
If the watch isn’t beneath guarantee, you should still be capable to get it repaired. You possibly can take it to a Rolex licensed supplier or to a certified watchmaker. The price of the restore will range relying on the difficulty.
Problem: I’ve misplaced the particular Rolex device.
In case you have misplaced the particular Rolex device, you should buy a substitute from a Rolex licensed supplier. The price of the device is $15.
Problem: The case again remains to be caught.
If the case again remains to be caught after following the steps above, chances are you’ll want to make use of a rubber mallet to faucet it gently. Watch out to not hit the case again too exhausting, as chances are you’ll injury the watch.
Problem: I’ve broken the watch.
In case you have broken the watch whereas making an attempt to take away the again, it’s best to take it to a Rolex licensed supplier for restore. The price of the restore will range relying on the extent of the injury.
Problem: I’m not comfy eradicating the again of the watch myself.
If you’re not comfy eradicating the again of the watch your self, you’ll be able to take it to a Rolex licensed supplier or to a certified watchmaker. They’ll be capable to take away the again of the look ahead to you.
Reattaching the Caseback
7. Tightening the Caseback
Gently tighten the caseback onto the watch head utilizing a caseback wrench or spanner. It is essential to use gradual and even stress to stop injury or overtightening.
Flip the wrench clockwise to regularly tighten the caseback till it is seated towards the gasket. Keep away from extreme power to stop distortion or injury.
As soon as the caseback is securely tightened, recheck the gasket for correct seating and any indicators of injury. If the gasket is broken or improperly seated, it could compromise the watch’s water resistance.
| Stress | Time |
|---|---|
| Mild-to-moderate | 5-10 seconds |
| Agency | 10-15 seconds |
| Comfortable | 15-20 seconds |
The best tightness varies relying on the particular watch mannequin and its water resistance score. In case you’re uncertain concerning the applicable stress, seek the advice of the producer’s tips or search skilled watch restore help.
Tightening the Caseback
After cleansing, it’s time to tighten the caseback onto the watch. This may be completed by hand or utilizing a caseback press.
To tighten the caseback by hand, merely maintain the watch in a single hand and the caseback within the different. Align the 2 elements and gently press them collectively. You need to really feel a slight click on because the caseback snaps into place.
To tighten the caseback utilizing a caseback press, observe these steps:
- Place the watch within the caseback press.
- Align the caseback with the gasket.
- Gently press the caseback into place.
- Tighten the caseback press till the caseback is cosy.
- Take away the watch from the caseback press.
To make sure that the caseback is tightened correctly, it is very important use a torque wrench. A torque wrench is a device that measures the quantity of power that’s utilized to a screw. This helps to stop the caseback from being overtightened or undertightened.
The proper torque for tightening a Rolex caseback is 5 Nm. Which means that 5 newton-meters of power ought to be utilized to the caseback.
In case you wouldn’t have a torque wrench, you should use a caseback device. A caseback device is a device that helps to tighten and loosen casebacks. Caseback instruments can be found at most jewellery shops and on-line retailers.
To tighten the caseback utilizing a caseback device, observe these steps:
- Place the caseback device on the caseback.
- Gently flip the caseback device till the caseback is cosy.
- Take away the caseback device.
As soon as the caseback is tightened, it is very important examine the gasket. The gasket is a rubber seal that helps to maintain water and dirt out of the watch. If the gasket is broken or worn, it ought to be changed.
To examine the gasket, merely take a look at it for any indicators of injury. If the gasket is broken, it ought to be changed with a brand new one.
Stress Testing (for Waterproof Watches)
After you have eliminated the again of your Rolex watch, it is very important stress take a look at it to make sure that it’s nonetheless waterproof. That is particularly necessary if you happen to plan on taking your watch swimming or diving. To stress take a look at your watch, you will want a stress tester. These could be bought on-line or at most jewellery shops.
To stress take a look at your watch, observe these steps:
- Place your watch within the stress tester.
- Shut the lid of the stress tester and tighten the screws.
- Pump the stress tester till the stress reaches the specified degree (often 3 or 6 atmospheres)
- Wait 1 minute to permit the watch to stabilize.
- Examine the look ahead to any leaks. If there aren’t any leaks, the watch is waterproof.
In case your watch fails the stress take a look at, it is very important have it inspected by a certified watchmaker. They’ll be capable to establish and repair the leak in order that your watch is as soon as once more waterproof.
Here’s a desk that summarizes the steps for stress testing a Rolex watch:
| Step | Description |
|---|---|
| 1 | Place your watch within the stress tester. |
| 2 | Shut the lid of the stress tester and tighten the screws. |
| 3 | Pump the stress tester till the stress reaches the specified degree (often 3 or 6 atmospheres) |
| 4 | Wait 1 minute to permit the watch to stabilize. |
| 5 | Examine the look ahead to any leaks. If there aren’t any leaks, the watch is waterproof. |
Aftercare and Upkeep
After you have efficiently eliminated the again of your Rolex watch, it is necessary to take correct care of it to make sure its longevity and performance:
1. Clear the Gasket
The gasket is a vital part that seals the again of the watch and prevents water from getting into. To take care of its integrity, use a tender, lint-free material to softly wipe away any filth or particles. Keep away from utilizing harsh chemical substances or solvents, as they’ll injury the gasket.
2. Examine the Seal
Earlier than reattaching the again, rigorously examine the seal. If there are any cracks, tears, or distortions, the watch might not be waterproof. On this case, it is really helpful to hunt skilled help.
3. Lubricate the Gasket
Making use of a small quantity of silicone grease to the gasket will assist enhance its sealing capabilities and stop dryness. Use a toothpick or small brush to use the lubricant evenly.
4. Tighten the Again
Use the particular device or your fingers to rigorously tighten the again of the watch. Keep away from overtightening, as this may injury the case or the again.
5. Stress Take a look at
In case you’re planning to submerge your watch in water, it is clever to carry out a stress take a look at. This may be completed by taking your watch to an authorized watchmaker who has the required gear.
6. Retailer Correctly
When not in use, retailer your Rolex watch in a cool, dry place away from direct daylight. This can assist forestall tarnishing and injury.
7. Common Servicing
Common upkeep is important for protecting your Rolex watch in optimum situation. Each few years, take your watch to an authorized watchmaker for cleansing, lubrication, and changes.
How you can Take away the Again of a Rolex Watch
Rolex watches are identified for his or her sturdiness and precision, however even probably the most well-made watch will must be serviced sometimes. Probably the most widespread service procedures is eradicating the again of the watch to entry the motion. This could be a difficult activity, however it’s doable to do it your self with the correct instruments and information.
Here’s a step-by-step information on learn how to take away the again of a Rolex watch:
- Collect your instruments. You will have a case knife, a case opener, and a rubber mallet.
- Place the watch in a vise. Guarantee that the vise is padded to guard the watch from injury.
- Use the case knife to pry open the case again. Watch out to not injury the case or the crystal.
- As soon as the case again is open, use the case opener to take away the motion. Watch out to not contact the motion along with your fingers.
- Examine the motion for any injury. If there’s any injury, it’s best to take the watch to a certified watchmaker for restore.
- If the motion is in good situation, you’ll be able to reassemble the watch. Begin by putting the motion again into the case. Then, use the case opener to screw on the case again.
- Lastly, use the rubber mallet to faucet the case again into place.
Folks Additionally Ask
How do I do know if my Rolex is actual?
There are a couple of methods to inform in case your Rolex is actual. First, search for the Rolex brand on the dial, case, and clasp. The brand ought to be crisp and clear, and the letters ought to be evenly spaced. Second, examine the serial quantity on the case again. The serial quantity ought to match the serial quantity on the guarantee card. Lastly, take the watch to a certified watchmaker for inspection. They’ll be capable to inform you if the watch is actual or faux.
How a lot does it price to interchange a Rolex crystal?
The fee to interchange a Rolex crystal will range relying on the mannequin of the watch and the kind of crystal. A primary crystal substitute will sometimes price between $100 and $200. A extra complicated crystal substitute, comparable to a sapphire crystal, can price as much as $1,000.
How usually ought to I service my Rolex watch?
Rolex watches are designed to be sturdy and exact, however they’ll must be serviced sometimes. The frequency of service will rely on how usually the watch is worn and the situations by which it’s worn. A normal rule of thumb is to have the watch serviced each 5 to 10 years.
